Power Supply 

SeventyPWR has 70W of output power (+12V / 2500mA, -12V / 2500mA and +5V / 2000mA). The design is based on the more powerful HammerPWR PSU with few upgrades.

SeventyPWR PSU is targeted to all who want enough power, low noise, high efficiency, best filtering, and a high level of power stability and secure protection for all modules in the Eurorack case.

The narrow shape of SeventyPWR allows it to mount between two bus boards. A double output terminal connects wires separately to two (or four) bus boards. This minimalizes the wire length and impedance of the power network. SeventyPWR works perfectly with all standard bus boards.

A special feature of SeventyPWR is the possibility to adjust output voltage in a safe range. Output voltages +12V and -12V are factory adjusted with an accuracy of 0,1% or better. Adjusting features can compensate for voltage drops on wires under load. This feature allows setting very accurate voltage directly on the module’s power inputs.

As is our practice SeventyPWR comes with overvoltage, over temperature, over current, short current, overload, and input reverse polarity protection. There are two stages of input filters which decrease noise from power brick and the electrical grid.

SeventyPWR is safely + externally powered from a 90W power brick (Meanwell GSM90A19-P1M – sold separately ) to make sure you and your modules are safe as well under all conditions. The inlet panel with connector and switch comes with PSU as basic accessories.

SeventyPWR ideal choice for any system including skiff and DIY where depth and size can be your concern.

Easy to install the push-to-connect system – WAGO 256 series shockproof + push-to-connect terminals ensure easy installation of SeventyPWR within your case.

Downloads

SeventyPWR wiring diagram – Diagram for an understanding of input and output wires connection. ( Busboards are sold separately )
Inlet Panel – dimensions and cutout diagram

Details

• SeventyPWR delivers: 12V / 2500mA, -12V / 2500mA and +5V / 2000mA
• Size: 13 × 16 × 2 cm
• Weight: 300g
• Output power: 70W
• Input: 19V DC

Power Supply 

HammerPWR is a reply to requests from users to provide a definite eurorack modular power supply that would be able to sustain and protect the most “busy” of setups. This eurorack modular power supply is developed to provide stable and clean power and further address many of the intrinsic topics which plague the daily eurorack modular musician.
Why name HammerPWR you ask? It is quite simple. It packs a powerful 100W unit with an output that can supply enough juice to the most hardcore eurorack system out there. Two of these will get your eurorack modular system rig going for a lifetime.

HammerPWR is  a strong eurorack modular power supply meant for use in the hardest of conditions on the market featuring the highest power density money can buy. The ideal solution for the largest of systems featuring many power-hungry analog/digital modules or modules which draw a lot of current needed for their ensured smooth operation. The system of filtered protection on the inputs and outputs of the power supply stays in place with minor tweaks to its core design making sure that your system will keep operating under hassle-free, low-noise, artifact-free conditions while also being protected from noises present in the power grid at times so your system and modules are safe and intact from external occurrences, mishaps, and influences. To ensure the lowest possible noise within your system there are a special type of converter used with low noise on their outputs and the +12V / 5A line is split into two branches by 2,5A + 2,5A to further decrease inherent influence between modules. Two sets of output terminals then further elevate the stress of cables connected to the bus board for longer service life.

HammerPWR is safely + externally powered from a GST120A20-P1M ( sold separately ) to make sure you and your modules are safe as well under all conditions.

The small dimensions of HammerPWR make it an ideal choice for any system including skiff and DIY where depth and size can be your concern.

Easy to install the push-to-connect system – WAGO 256 series shockproof + push-to-connect terminals ensure easy installation of HammerPWR within your case.

Downloads

HammerPWR wiring diagram – Diagram for an understanding of input and output wires connection. ( Busboards are sold separately )
Inlet Panel – dimensions and cutout diagram

Details

• BoardPWR delivers: 12V / 5A (splited to two branches 2.5A + 2.5A), -12V / 2.5A and +5V / 2A
• Size: 10 × 10 × 2 cm
• Weight: 300g
• Output power: 100W
• Input: 20V DC

Power Supply 

BoardPWR is safely supplied from an external DC power brick (16-20V). It is possible to chain more boards together in one case and feed them from one power brick altogether.
We recommend Meanwell GSM60A18-P1J DC Power Brick for one BoardPWR PSU and GST120A20-P1M for two BoardPWR PSU solutions.

Connectors

There are two types of output connections. You can either connect bus boards via two 16pins IDC headers (ideal for flying bus boards) or via high-quality WAGO spring terminals.

Details

• BoardPWR delivers: 12V / 2A, -12V / 1.2A and +5V/1.5A
• Size: 10 × 4.5 × 2 cm
• Weight: 127 g
• Output power: 45W
• Input: 18V (16-20V)

To work properly it requires 90W power adapter. We recommend this adapter : GST90A15-P1M

DETAILS

• 80 Watt integrated switching power supply

• Low impedance star distribution due to 4 layer PCB

• +12V output at 3000 mA, -12V output at 3000 mA, +5V output at 1500 mA

• Triple 120° phased controller for low induced noise

• Output short circuit protection and foldback current limiting

• Output overvoltage protection from transient overshooting

• Soft start for controlled start up operation

• +/-1% output voltage accuracy

• Fits comfortably in an 84HP  3U case or 6U case and larger

• 34cm wide  x 8cm tall and max height of 20mm.

• Mounting holes can be used with 0.157″ / 4mm PEM snaps for quick install.