Include VAT

HammerPWR_Konstant Lab – 100W Eurorack modular power supply

(2 customer reviews)

219.00 Excl. VAT

Konstant Lab HammerPWR is is a powerful 100W unit with an output that can supply enough juice to the most hardcore eurorack system out there.

 

Available on backorder

Konstant Lab HammerPWR is is a powerful 100W unit with an output that can supply enough juice to the most hardcore eurorack system out there.

Power Supply 

HammerPWR is a reply to requests from users to provide a definite eurorack modular power supply that would be able to sustain and protect the most “busy” of setups. This eurorack modular power supply is developed to provide stable and clean power and further address many of the intrinsic topics which plague the daily eurorack modular musician.
Why name HammerPWR you ask? It is quite simple. It packs a powerful 100W unit with an output that can supply enough juice to the most hardcore eurorack system out there. Two of these will get your eurorack modular system rig going for a lifetime.

HammerPWR is  a strong eurorack modular power supply meant for use in the hardest of conditions on the market featuring the highest power density money can buy. The ideal solution for the largest of systems featuring many power-hungry analog/digital modules or modules which draw a lot of current needed for their ensured smooth operation. The system of filtered protection on the inputs and outputs of the power supply stays in place with minor tweaks to its core design making sure that your system will keep operating under hassle-free, low-noise, artifact-free conditions while also being protected from noises present in the power grid at times so your system and modules are safe and intact from external occurrences, mishaps, and influences. To ensure the lowest possible noise within your system there are a special type of converter used with low noise on their outputs and the +12V / 5A line is split into two branches by 2,5A + 2,5A to further decrease inherent influence between modules. Two sets of output terminals then further elevate the stress of cables connected to the bus board for longer service life.

HammerPWR is safely + externally powered from a GST120A20-P1M ( sold separately ) to make sure you and your modules are safe as well under all conditions.

The small dimensions of HammerPWR make it an ideal choice for any system including skiff and DIY where depth and size can be your concern.

Easy to install the push-to-connect system – WAGO 256 series shockproof + push-to-connect terminals ensure easy installation of HammerPWR within your case.

Downloads

HammerPWR wiring diagram – Diagram for an understanding of input and output wires connection. ( Busboards are sold separately )
Inlet Panel – dimensions and cutout diagram

 

Details

  • BoardPWR delivers: 12V / 5A (splited to two branches 2.5A + 2.5A), -12V / 2.5A and +5V / 2A
  • Size: 10 × 10 × 2 cm
  • Weight: 300g
  • Output power: 100W
  • Input: 20V DC
Weight 0.3 kg
DIMENSIONS

10 × 10 × 2 cm, 300 g

OUTPUT POWER

100W

OUTPUTS

+12V / 5A (splited to two branches 2.5A + 2.5A), -12V / 2.5A, +5V / 2A

INPUT

20V DC

OUTPUT CONNECTORS

16 pin IDC for flat cable, 8x WAGO spring terminals

INPUT CONNECTORS

WAGO spring terminals, Panel with 5,5 x 2.5 DC input (center positive) and switch included

PROTECTIONS

Input filter, Input overvoltage, Input reverse polarity voltage protection, Output overvoltage, Output short circuit – automatic recovery, Output over current – automatic recovery, All output protections are independent for each rail

EFFICIENCY

90%

OTHER

Dual input common mode LC filter with high efficiency of canceling noise and interference from input connector, Additional input filter for each converter for minimal output noise and interferences
LEDs indicate present and drop of output voltage, +12V output is split to two branches for modules separation and minimalize of voltage dropout

ACCESSORIES

Aluminum panel with 5,5 x 2.5 DC input (center positive), power switch, and two 25cm wires, Screws 2,9 x 13mm 4pcs, Spacers 3mm height 4pcs

2 reviews for HammerPWR_Konstant Lab – 100W Eurorack modular power supply

5.0
Based on 2 reviews
5 star
100
100%
4 star
0%
3 star
0%
2 star
0%
1 star
0%
  1. Anonymous (verified owner)

  2. Guillaume (verified owner)

Only logged in customers who have purchased this product may leave a review.

Content missing

Scroll to Top